Package Contents Check the following contents of your package: PoE Switch x 1 User Guide x1 Power Cord x1 Accessories(Rack Mount Accessory Kit*2 ,Rubber Feet*4, screw*8) If any part is lost and damaged, please contact your local agent immediately.
Introduction PM3010GSNL contains 10 RJ45 ports and 1~8 support PoE functions. The PoE ports can automatically detect and supply power to IEEE802.3af/at compliant Powered Devices (PD). The electrical power and data transmission on the same cable can expand your network to the places where no power lines or outlets, where you can install devices such as APs, IP cameras, or IP phones etc. The LCD not only can display the PoE work status, accurate judgment port of load, can also help customer and engineer timely discover and solve the network failure, improve work efficiency and quality. The PM3010GSNL has VLAN function that improve the network environment and reduces network maintenance costs.
Hardware Description Front Panel The Front Panel Consists of Ethernet Ports. The LED indicators and LCD are also located on the panel.
PoE Status The PoE Switch is with the function of the LCD display and PoE. The LCD can display the working condition of PoE port not only, still can accurately show the state of each port, such as: Output power, Overload, Short circuit, Light load, Low voltage, Over voltage,High temperature, and so on...
DIP Switch The DIP switch located on the left panel. Standard: the factory default mode, can normal communication between port 1~10. VLAN: 1-8 port can be isolated each other but 1-8 port can connect to 9/10 port after open VLAN to stop broadcast storm to increase forwarding rate of frame. Extend: Up to 250m PoE distance allows you to expand you network via Ethernet cable to where there is no power line or outlet but where you want to fix device such as IP Cameras. LED indicator LED
Off: No Power supply. Light: Indicates the switch has power.
Off: No device is connected to the corresponding port. Light: Indicates the link through that port is successfully established at 10/100Mbps. Blink: Indicates that the Switch is actively sending or receiving data over that port.
Off: No device is connected to the corresponding port. Light: Indicates the link through that port is successfully established at 1000Mbps. Blink: Indicates that the Switch is actively sending or receiving data over that port.
Off: No PoE powered device (PD) connected. Light: There is a PoE PD connected to be port, which supply power successfully. Blink: Indicates port abnormal power supply.
Rear Panel The rear panel of the PoE Switch indicates an AC inlet power socket, which accepts input power from 100 to 240V AC, 50/60HZ.
Power socket Connect the female connector of the power cord here, and the male connector to the AC(Alternating Current) power outlet. Please make sure the voltage of the power supply meets the requirement of the input voltage Grounding column The switch already comes with lightning protection mechanism. You can also ground the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.
Installation the Switch This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions in avoid of incorrect installation causing device damage and security threat. Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet cloth or liquid; Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis; Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall; Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction; Make sure that the operating voltage is the same one labeled on the switch; Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks. Desktop Installation Install the Switch on a desktop, please attach these cushioning rubber feet provided on the bottom at each corner of the Switch in case of the external vibration. Allow adequate space for ventilation between the device and the objects around it.
Rack-mountable Installation The switch is rack-mountable and can be installed on an EIA-19 inch equipment rack. To do this, first, please install the mounting brackets on the switch’s side panels (one on each side), secure them with the included screws, and then use the screws provided with the equipment rack to mount the switch on the 19 inch rack.
Turn on the switch Please connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded ). When the switch is power on, the LED indicators flash momentarily for one second, which represents a resetting of the system.The Power LED indicator turns on green. Note: Please confirm the voltage is correct before power on, otherwise the switch will be damaged. (The power input is:100V-240Vac, 50/60Hz.)
Specifications Model Standard Network Media MAC Address Table Transfer mode Frame Forward Rate Switching Capacity Dimensions (L*W*H) Fan Quantity Power Input PoE Port PoE Power on RJ45 PoE Power Output PoE Power Budget Temperature Humidity